BadUSB with MicroSD

$19.99

This is one of the last developments related to rubberducky or badusb devices. This device is based on the ATMEGA32U4 microprocessor which is able to emulate many USB modes like HID, used for injecting key presses to the target system.

BadUSB with MicroSD

$19.99

Specifications

Controller

ATmega32u4

Working Frequency

Analog Channel

12

PWM Channel

7

Memory

32KB

SRAM

2.5KB

EEPROM

1KB

Controller

ATmega32u4

Working Frequency

Analog Channel

12

PWM Channel

7

Memory

32KB

SRAM

2.5KB

EEPROM

1KB

Electronics

Working Voltage

5V

Working Voltage

5V

Controller

ATmega32u4

Working Frequency

Working Voltage

5V

Analog Channel

12

PWM Channel

7

Memory

32KB

SRAM

2.5KB

EEPROM

1KB

This is one of the last developments related to rubber ducky or bad USB devices. This device is based on the ATMEGA32U4 microprocessor which can emulate many USB modes like HID, used for injecting key presses to the target system.

The main processor is based on the Arduino Leonardo R3 development board and the improvement is that a microSD card slot is included to allow storing many different payloads. The microSD card has to be FAT32 formatted to be recognized.

You can find the firmware and the instructions for flashing it in the following github:

Specifications

  • High Performance, Low Power AVR® 8-Bit Microcontroller Advanced RISC Architecture
  • 16/32KB of In-System Self-Programmable Flash
  • 1.25/2.5KB Internal SRAM – 512Bytes/1KB Internal EEPROM
  • Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface USB 2.0 Fullspeed/
  • Low Speed
  • CPU Reset possible on USB Bus Reset detection
  • 48MHz from PLL for Full-speed Bus Operation
  • USB Bus Connection/Disconnection on Microcontroller Request
  • Crystal-less operation for Low-Speed mode Peripheral Features
  • On-chip PLL for USB and High-Speed Timer: 32 up to 96MHz operation
  • One 8-bit Timer/Counter with Separate Prescaler and Compare Mode ATmega16U4/ATmega32U4 8-
  • bit Microcontroller with 16/32K bytes of ISP Flash and USB Controller
  • One 10-bit High-Speed Timer/Counter with PLL (64MHz) and Compare Mode
  • Four PWM Channels with Programmable Resolution from 2 to 16 Bits
  • Six PWM Channels for High-Speed Operation, with Programmable Resolution from 2 to 11 Bits
  • Output Compare Modulator – 12-channels, 10-bit ADC (features Differential Channels with
  • Programmable Gain)
  • Programmable Serial USART with Hardware Flow Control
  • Master/Slave SPI Serial Interface
  • Operating Voltages 2.7 – 5.5V Operating temperature

Reviews

There are no reviews yet.

Be the first to review “BadUSB with MicroSD”

Your email address will not be published. Required fields are marked *

Q & A

There are no questions yet

Ask a question

Your question will be answered by a store representative or other customers.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Thank you for the question!

Your question has been received and will be answered soon. Please do not submit the same question again.

Error

Warning

An error occurred when saving your question. Please report it to the website administrator. Additional information:

Add an answer

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Thank you for the answer!

Your answer has been received and will be published soon. Please do not submit the same answer again.

Error

Warning

An error occurred when saving your question. Please report it to the website administrator. Additional information: